WireGuard LXC Alpine Linux

100 % Testé et approuvé

   

ProxMox

source

Côté serveur :

# apt update && apt upgrade
# apt install pve-headers
# echo 'deb http://deb.debian.org/debian buster-backports main' >> /etc/apt/sources.list
# apt update
# apt install -t buster-backports wireguard-dkms
# modprobe wireguard
# echo "wireguard" >> /etc/modules-load.d/modules.conf

LXC Alpine 3.12

WireGuard Server

HDD : 0,5G / CPU : 1 / RAM : 256mb ??

Avec un téléphone android connecté !!! :

On autorise el routage :

# echo 'net.ipv4.ip_forward=1' >> /etc/sysctl.conf
# sysctl -p

net.ipv4.ip_forward = 1

# rc-update add sysctl default

Puis on install :

# apk update && apk upgrade
# apk add wireguard-tools

On récup la configuration sur wireguardconfig

# vi /etc/wireguard/wg0.conf

[Interface]
Address = 10.0.0.1/24
ListenPort = 51820
PrivateKey = *****************************************
PostUp = iptables -A FORWARD -i %i -j ACCEPT; iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
PostDown = iptables -D FORWARD -i %i -j ACCEPT; iptables -t nat -D POSTROUTING -o eth0 -j MASQUERADE

[Peer]
PublicKey = *****************************************
PresharedKey = *****************************************
AllowedIPs = 10.0.0.2/32

[Peer]
PublicKey = *****************************************
PresharedKey = *****************************************
AllowedIPs = 10.0.0.3/32

[Peer]
PublicKey = *****************************************
PresharedKey = *****************************************
AllowedIPs = 10.0.0.4/32

# vi /etc/wireguard/client1.conf

[Interface]
Address = 10.0.0.2/24
ListenPort = 51820
PrivateKey = *****************************************

[Peer]
PublicKey = *****************************************
PresharedKey = *****************************************
AllowedIPs = 0.0.0.0/1, 128.0.0.0/1
Endpoint = myserver.dyndns.org:51820

Allowed IP modifié pour ne pas redirigé tout le traffic local..

Test

# wg-quick up wg0

[#] ip link add wg0 type wireguard
[#] wg setconf wg0 /dev/fd/63
[#] ip -4 address add 10.0.0.1/24 dev wg0
[#] ip link set mtu 1420 up dev wg0
[#] iptables -A FORWARD -i wg0 -j ACCEPT; iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE

# wg

interface: wg0
  public key: *****************************************
  private key: (hidden)
  listening port: 51820

peer: *****************************************
  preshared key: (hidden)
  allowed ips: 10.0.0.2/32

peer: *****************************************
  preshared key: (hidden)
  allowed ips: 10.0.0.3/32

peer: *****************************************
  preshared key: (hidden)
  allowed ips: 10.0.0.4/32

Fin du test :

# wg-quick down wg0

[#] ip link delete dev wg0
[#] iptables -D FORWARD -i wg0 -j ACCEPT; iptables -t nat -D POSTROUTING -o eth0 -j MASQUERADE

wg0 au boot via init.d

source

# vi /etc/init.d/wireguard

#!/sbin/openrc-run

depend() {
   need localmount
   need net
}

start() {
   ebegin "Starting wireguard"
   /usr/bin/wg-quick up wg0
   eend $?
}

stop() {
   ebegin "Stopping wireguard"
   /usr/bin/wg-quick down wg0
   eend $?
}

# chmod +x /etc/init.d/wireguard

# rc-update add wireguard default

On lance :

# service wireguard start

On peut tester avec "wg", rebooter pour vérifier etc...

(Optionnel) QR Code

# apk add libqrencode

Exemple :

# qrencode -t ansiutf8 < /etc/wireguard/client1.conf

voila!